automobilių detalių žinynas
 | Viso detalių : 0 |
Mano miestas
Pagrindinis meniu
Transporto priemonė: TYP 180a BM 120.010, .011; VIN numerio dalis: 120011
Grupė: 54 ELECTRICAL EQUIPMENT AND INSTRUMENTS
| # | Kodas | Pavadinimas |
|---|---|---|
| X XXXXXXXXXXXX | PART NAME MISSING | |
| BATTERY, STARTER CABLE | ||
| 001 | A 0005414601 | LEAD BATTERY 12 V |
| A 0005411201 | LEAD BATTERY 12 V | |
| SPECIAL REQUEST (TROPICAL DESIGN) | ||
| 002 | A 1215400123 | FIXING FRAME |
| 003 | A 1205410124 | TIGHTENING SCREW |
| FOR FIXING OF BATTERY | ||
| LOCK WASHER | ||
| B 6 DIN 127 FOR FIXING OF BATTERY | ||
| HEX. NUT | ||
| M 6 DIN 934-5 S FOR FIXING OF BATTERY | ||
| A 0009870532 | RUBBER HOSE, 20 MM LONG | |
| OVER ANGLE OF SUPPORTING RAIL, BATTERY ORDER BY THE METER | ||
| 004 | A 0009870315 | RUBBER PLUG |
| FOR BLIND HOLE IN FRONT WALL AND SUPPORTING RAIL | ||
| A 1805400030 | STARTER CABLE | |
| FROM POS. POLE TO STARTER MOTOR | ||
| 006 | A 1285400030 | STARTER CABLE |
| FROM POS. POLE TO STARTER MOTOR | ||
| A 1215400130 | STARTER CABLE | |
| FROM POS. POLE TO STARTER MOTOR | ||
| 007 | A 1365460035 | RUBBER PROTECTIVE CAP |
| FOR STARTER CABLE | ||
| 008 | A 1805400031 | GROUND CABLE |
| FROM NEG. POLE OF BATTERY TO CLUTCH HOUSING | ||
| A 1805400431 | GROUND CABLE | |
| FROM NEG. POLE OF BATTERY TO CLUTCH HOUSING | ||
| A 1869970481 | GROMMET | |
| FOR STARTER CABLE THROUGH BRACKET TO FRONT WALL | ||
| LOCK WASHER | ||
| B 6 DIN 127 FOR STARTER CABLE THROUGH BRACKET TO FRONT WALL | ||
| LENS-HD. SCREW | ||
| AM 6X8 DIN 7985-4 S FOR STARTER CABLE THROUGH BRACKET AT FRONT WALL | ||
| A 0009973481 | GROMMET | |
| FOR STARTER CABLE THROUGH FIXING ANGLE, FRONT WALL | ||
| 009 | A 1879950037 | FIXING CLAMP |
| FOR CABLE TO STARTER MOTOR AT COWL OR AT MOUNTING CONTROL SHAFT, RESPECTIVELY | ||
| A 1819950020 | FIXING CLAMP | |
| FOR CABLE TO STARTER MOTOR AT COWL OR AT MOUNTING CONTROL SHAFT, RESPECTIVELY | ||
| LENS-HD. SHEET | ||
| METAL SCREW BZ 4,8X9,5 DIN 7981 FOR CABLE TO STARTER MOTOR AT COWL OR AT MOUNTING CONTROL SHAFT, RESPECTIVELY | ||
| LENS-HD. SCREW | ||
| AM 5X10 DIN 7985-4 S FOR CABLE TO STARTER MOTOR AT COWL OR AT MOUNTING CONTROL SHAFT, RESPECTIVELY | ||
| LOCK WASHER | ||
| B 5 DIN 127 FOR CABLE TO STARTER MOTOR AT COWL OR AT MOUNTING CONTROL SHAFT, RESPECTIVELY | ||
| X XXXXXXXXXXXX | PART NAME MISSING | |
| CABLES | ||
| A 1205402405 | REPLACED BY | |
| 120 540 26 05 TOGETHER WITH 1 FUSE BOX 180 540 09 50 UP TO CHASSIS 7503258 | ||
| 015 | A 1205402605 | MAIN CABLE HARNESS |
| FROM CHASSIS 7503259 | ||
| A 1205402705 | MAIN CABLE HARNESS | |
| 016 | A 0005450628 | HOUSING, LOWER |
| PART, WITH SOCKET | ||
| 017 | A 0005450080 | GASKET |
| 018 | A 1215400807 | CABLE HARNESS |
| 019 | A 1805400008 | CABLE HARNESS |
| FROM GENERATOR TO REGULATOR | ||
| 021 | A 0005460235 | RUBBER PROTECTIVE CAP |
| FOR TERMINAL AT GENERATOR D POS. AND DF | ||
| INSULATING HOSE | ||
| B 16X18 SW 200 1G DIN 40621 OVER MAIN CABLE HAMESS, ROTARY SWITCH ORDER BY THE METER | ||
| 023 | A 1205401738 | CABLE HARNESS |
| FROM 2-POLE CABLE CONNECTOR TO REVERSE DRIVE LIGHT | ||
| 024 | A 1805460043 | BRACKET |
| FOR CABLE HARNESS AT REVERSE DRIVE LIGHT SWITCH | ||
| 025 | A 0009973181 | GROMMET |
| FOR CABLE HARNESS AT BRACKET | ||
| A 1819950020 | FIXING CLAMP | |
| FOR CABLE OF REV. DRIVE LIGHT SWITCH AT PEDAL FLOOR, RIGHT | ||
| LENS-HEAD SHEET | ||
| METAL SCREW BZ 4,8X9,5 DIN 7981 FOR CABLE OF REV. DRIVE LIGHT SWITCH AT PEDAL FLOOR, RIGHT | ||
| A 1365400441 | GROUND CABLE | |
| FROM STARTER FLANGE TO FRONT WALL | ||
| 026 | A 1865400341 | GROUND CABLE |
| FROM STARTER FLANGE TO FRONT WALL | ||
| A 1205400041 | GROUND CABLE | |
| FROM STARTER FLANGE TO FRONT WALL | ||
| 027 | A 1204200227 | SCREW WITH LOCKING PLATE |
| FOR GROUND CABLE AT PEDAL FLOOR | ||
| LOCK WASHER | ||
| B 6 DIN 127 FOR GROUND CABLE AT PEDAL FLOOR | ||
| HEX. NUT | ||
| M 6 DIN 934-5 S FOR GROUND CABLE AT PEDAL FLOOR | ||
| 031 | A 0005461941 | CABLE CONNECTOR, 5-POLE |
| FOR TAIL LIGHT CABLE HARNESS | ||
| 032 | A 0005460641 | CABLE CONNECTOR, 5-POLE |
| FOR STEERING SPINDLE CABLE HARNESS | ||
| 033 | A 0005461841 | CABLE CONNECTOR 2-POLE |
| FOR HEATER BLOWER CONNECTION | ||
| LENS-HEAD SHEET | ||
| METAL SCREW B 3,9X9,5 DIN 7981 FOR 5-POLE CABLE CONNECTOR AT FRONT WALL | ||
| LENS-HEAD SHEET | ||
| METAL SCREW B 3,9X19 DIN 7981 FOR 5-POLE CABLE CONNECTOR AT WHEEL HOUSE, STEERING SPINDLE CABLE HARNESS | ||
| LENS-HEAD SHEET | ||
| METAL SCREW B 3,9X13 DIN 7981 FOR 2-POLE CABLE CONNECTOR AT WHEEL ARCH PAN, LEFT AND RIGHT, HEATER BLOWER | ||
| 037 | A 1819970081 | GROMMET |
| FOR MAIN CABLE HARNESS THROUGH FRONT WALL | ||
| 038 | A 0009972781 | GROMMET |
| FOR MAIN CABLE HARNESS THROUGH FRONT WALL | ||
| 38a | A 0009972281 | GROMMET |
| FOR BLINKER THROUGH WHEEL ARCH FOR MAIN CABLE HARNESS THROUGH FRONT WALL | ||
| 039 | A 0009883378 | CLAMP WITH LUG |
| FOR MAIN CABLE HARNESS AT FRONT WALL | ||
| 039 | A 0009883378 | CLAMP WITH LUG |
| FOR MAIN CABLE HARNESS AT FRONT WALL | ||
| 040 | A 0009883478 | CLAMP WITH LUG |
| FOR MAIN CABLE HARNESS AT FRONT WALL | ||
| 040 | A 0009883478 | CLAMP WITH LUG |
| FOR MAIN CABLE HARNESS AT FRONT WALL | ||
| A 1805403038 | GROUND CABLE | |
| FOR PARKING LIGHT WITH ASYMMETRIC DIMMER LIGHT FROM CHASSIS 7502539 UP TO CHASSIS 7503258 | ||
| 042 | A 0009971781 | RUBBER SLEEVE |
| FOR FUEL TRANSMITTER CABLE | ||
| A 0009973081 | RUBBER SLEEVE | |
| FOR GLOVE BOX | ||
| A 0009883378 | CLIP WITH LUG | |
| FOR TAIL LIGHT CABLE HARNESS AT COVER PLATE AND FOR CABLE TO HORN | ||
| A 0009883478 | CLIP WITH LUG | |
| FOR TAIL LIGHT CABLE HARNESS AT COVER PLATE AND FOR CABLE TO HORN | ||
| LENS-HD.SHEET METAL SCREW | ||
| B 4,8X9,5 DIN 7981 F.GROUND CABLE, TRANSMITTER AT REAR CROSS MEMBER | ||
| 056 | A 1205460182 | BRACKET |
| FOR TAIL LIGHT CABLE HARNESS, LEFT AND RIGHT | ||
| LOCK WASHER | ||
| B 4 DIN 127 FOR GROUND CONNECTION AT LUGGAGE COMPARTMENT FOR TAIL LIGHT | ||
| LENS-HEAD SCREW | ||
| AM 4X10 DIN 7985-4 S FOR GROUND CONNECTION AT LUGGAGE COMPARTMENT FOR TAIL LIGHT | ||
| HEX. NUT | ||
| M 4 DIN 934-5 S FOR GROUND CONNECTION AT LUGGAGE COMPARTMENT FOR TAIL LIGHT | ||
| 061 | A 1205460081 | CABLE COVER PLATE |
| FOR CABLE PROTECTIVE PLATE AT REAR CROSS MEMBER | ||
| LENS-HEAD SHEET | ||
| METAL SCREW B 3,9X13 DIN 7981 FOR CABLE PROTECTIVE PLATE AT REAR CROSS MEMBER | ||
| 063 | A 1369950037 | FIXING CLAMP |
| FOR MAIN CABLE HARNESS AT FRONT WALL | ||
| LENS-HEAD SCREW | ||
| AM 4X12 DIN 7985-4 S FOR MAIN CABLE HARNESS AT FRONT WALL | ||
| LOCK WASHER | ||
| B 4 DIN 127 FOR MAIN CABLE HARNESS AT FRONT WALL | ||
| LENS-HEAD SCREW | ||
| AM 6X15 DIN 7985-4 S FOR MAIN CABLE HARNESS AT FRONT WALL | ||
| LOCK WASHER | ||
| B 6 DIN 127 FOR MAIN CABLE HARNESS AT FRONT WALL | ||
| 066 | A 0009902291 | CAGE CLIP WITH NUT |
| FOR MAIN CABLE HARNESS AT FRONT WALL | ||
| A 1809971582 | RUBBER HOSE, | |
| DIA 15X17, 20-MM LONG OVER STARTER MOTOR CABLE, GENERATOR CABLE AND MAIN CABLE HARNESS | ||
| 067 | A 0009974782 | RUBBER HOSE, |
| DIA 15X17, 20-MM LONG OVER STARTER MOTOR CABLE, GENERATOR CABLE AND MAIN CABLE HARNESS ORDER BY THE METER | ||
| 068 | A 1369950135 | FIXING CLAMP |
| FOR MAIN CABLE HARNESS AT FRONT WALL | ||
| 069 | A 1819950020 | FIXING CLAMP |
| FOR STEERING SPINDLE CABLE HARNESS AT FORKED SUPPORT | ||
| LENS-HEAD SHEET | ||
| METAL SCREW B 4,2X9,5 DIN 7981 FOR STEERING SPINDLE CABLE HARNESS AT FORKED SUPPORT | ||
| A 0019880978 | FIXING CLIP | |
| FOR CABLE, STOP SWITCH AT BRAKE FLUID PIPE | ||
| A 1805400350 | FUSE BOX | |
| WITH FUSE AND BRASS SCREW UP TO CHASSIS 7503258 | ||
| A 1215400750 | FUSE BOX | |
| WITH FUSE AND BRASS SCREW AB FGST. 7503259 | ||
| 071 | A 1805400950 | FUSE BOX |
| WITH FUSE AND BRASS SCREW AB FGST. 7503259 | ||
| 072 | A 0005450203 | COVER |
| FOR FUSE BOX | ||
| FUSE, 12 AMP. | ||
| 8 DIN 72581 UP TO CHASSIS 7503258 | ||
| FUSE, 12 AMP. | ||
| 8 DIN 72581 FROM CHASSIS 7503259 | ||
| FUSE, 35 AMP. | ||
| 25 DIN 72581 FROM CHASSIS 7503259 | ||
| A 1205403273 | BRACKET, LOWER PART | |
| FOR FUSE BOX UP TO CHASSIS 9503080 | ||
| 074 | A 1205450940 | BRACKET, LOWER PART |
| FOR FUSE BOX FROM CHASSIS 9503081 | ||
| 075 | A 1805450140 | BRACKET, UPPER PART |
| FOR FUSE BOX | ||
| LENS-HEAD SCREW | ||
| AM 6X12 DIN 7985-4 S FOR BRACKET AT COWL | ||
| LOCK WASHER | ||
| B 6 DIN 127 FOR BRACKET AT COWL | ||
| LENS-HEAD SHEET | ||
| METAL SCREW B 3,9 X 19 DIN 7981 FOR FUSE BOX TO BRACKET | ||
| A 0009941345 | SPRING NUT | |
| FOR FUSE BOX TO BRACKET | ||
| LENS-HEAD SCREW | ||
| AM 5X15 DIN 7985-4 S FOR FUSE BOX AT BRACKET, BOOSTER BRAKE SPECIAL REQUEST FOR INSTALLATION OF ATE BOOSTER BRAKE T 50 | ||
| LOCK WASHER | ||
| B 5 DIN 127 FOR FUSE BOX AT BRACKET, BOOSTER BRAKE SPECIAL REQUEST FOR INSTALLATION OF ATE BOOSTER BRAKE T 50 | ||
| HEX. NUT | ||
| M 5 DIN 934-5 S FOR FUSE BOX AT BRACKET, BOOSTER BRAKE SPECIAL REQUEST FOR INSTALLATION OF ATE BOOSTER BRAKE T 50 | ||
| 076 | A 1819950020 | FIXING CLAMP |
| FOR MAIN CABLE HARNESS AT REINFORCEMENT BRACKET, LEFT AND RIGHT | ||
| LENS-HEAD SCREW | ||
| AM 4X10 DIN 7985-4 S FOR MAIN CABLE HARNESS AT REINFORCEMENT BRACKET, LEFT AND RIGHT | ||
| LOCK WASHER | ||
| B 4 DIN 127 FOR MAIN CABLE HARNESS AT REINFORCEMENT BRACKET, LEFT AND RIGHT | ||
| 077 | A 1539950322 | FIXING CLAMP |
| FOR CABLE TO STOP LIGHT AND FOOT DIMMER SWITCH | ||
| LENS-HEAD SHEET | ||
| METAL SCREW B 4,8X9,5 DIN 7981 FOR CABLE TO STOP LIGHT AND FOOT DIMMER SWITCH | ||
| 078 | A 0009888878 | CLAMP |
| FOR MAIN CABLE HARNESS TO REVERSE DRIVE LIGHT AT GUTTER | ||
| 079 | A 1219950022 | FIXING CLAMP |
| FOR MAIN CABLE HARNESS AND BRAKE FLUID PIPE AT FRAME BOTTOM | ||
| HEX. HEAD | ||
| SHEET METAL SCREW B 6,3X16 DIN 7976 | ||
| X XXXXXXXXXXXX | PART NAME MISSING | |
| INSTRUMENTS AND SWITCHES | ||
| A 1205400044 | PUSH-BUTTON SWITCH | |
| FOR INSTRUMENT LIGHTING | ||
| 080 | A 0005450611 | PUSH-BUTTON SWITCH |
| FOR INSTRUMENT LIGHTING | ||
| 081 | A 1205450072 | ESCUTCHEON |
| 082 | A 0009972040 | FELT RING |
| 083 | A 1205450237 | BUTTON |
| 084 | A 1055420501 | COMBI-INSTRUMENT WITH |
| KILOMETER GRADUATION RATIO 0.91, RATIO OF REAR AXLE 1:3,9 | ||
| A 1055420601 | COMBI-INSTRUMENT WITH | |
| M.P.H. GRADUATION RATIO 1.47, RATIO OF REAR AXLE 1:3,9 EXPORT | ||
| A 1215420301 | COMBI-INSTRUMENT WITH | |
| KILOMETER GRADUATION RATIO 0.96, RATIO OF REAR AXLE 1:4.1 EXPORT FOR MADEIRA AND HONGKONG | ||
| A 1215420101 | COMBI-INSTRUMENT WITH | |
| M.P.H. GRADUATION RATIO 1.54, RATIO OF REAR AXLE 1:4.1 EXPORT FOR MADEIRA AND HONGKONG | ||
| A 1055420701 | COMBI-INSTRUMENT WITH | |
| M.P.H. GRADUATION RATIO 1,36, RATIO OF REAR AXLE 1:3,9 EXPORT, SPECIAL REQUEST FOR TIRES 6.40 - 15 | ||
| A 1055420801 | COMBI-INSTRUMENT WITH | |
| KILOMETER GRADUATION RATIO 0,845, RATIO OF REAR AXLE 1:3,9 EXPORT, SPECIAL REQUEST FOR TIRES 6.40 - 15 | ||
| 085 | A 0015427406 | KILOMETER COUNTER |
| RATIO 0.91, RATIO OF REAR AXLE 1:3.9 | ||
| A 0015424306 | KILOMETER COUNTER | |
| RATIO 0.96, RATIO OF REAR AXLE 1:4,1 EXPORT FOR MADEIRA AND HONGKONG | ||
| A 0015428006 | KILOMETER COUNTER | |
| RATIO 0.845, RATIO OF REAR AXLE 1:3.9 EXPORT, SPECIAL REQUEST FOR TIRES 6.40 - 15 | ||
| A 0015424206 | MILEAGE COUNTER | |
| RATIO 1.54, RATIO OF REAR AXLE 1:4,1 EXPORT FOR MADEIRA AND HONGKONG | ||
| A 0015427506 | MILEAGE COUNTER | |
| RATIO 1,47, RATIO OF REAR AXLE 1:3.9 EXPORT | ||
| A 0015428106 | MILEAGE COUNTER | |
| RATIO 1.36, RATIO OF REAR AXLE 1:3,9 EXPORT, SPECIAL REQUEST FOR TIRES 6.40 - 15 | ||
| 086 | A 0005427102 | OIL PRESSURE GAUGE |
| 087 | A 0015424405 | PART NAME MISSING |
| LENGTH OF CAPILLARY TUBE 1,700-MM | ||
| 088 | A 0005424403 | FUEL GAUGE |
| 089 | A 1209331710 | TENSION SPRING |
| FOR FIXING OF COMBI-INSTRUMENT | ||
| 090 | A 1205420280 | RUBBER FRAME |
| FOR COMBI-INSTRUMENT | ||
| 091 | A 0005450719 | LAMP SOCKET |
| BULB | ||
| H 12 V 2 W DIN 72601 | ||
| A 0009883478 | CLIP WITH LUG | |
| FOR HOUSING, UPPER PART AND LOWER PART AT GLOVE BOX COVER PLATE | ||
| 100 | A 1205420311 | CLOCK WITH MECHANIC DRIVE |
| 101 | A 0005450719 | LAMP SOCKET |
| BULB | ||
| H 12 V 2 W DIN 72601 | ||
| 109 | A 0005450831 | DIMMING RESISTOR |
| FOR INSTRUMENT LIGHTING | ||
| 110 | A 0005451714 | PUSH - |
| BUTTON STARTING SWITCH | ||
| 111 | A 1205450372 | ESCUTCHEON |
| FOR PUSH - BUTTON STARTING SWITCH | ||
| A 1805400660 | OIL PRESSURE GAUGE PIPE | |
| UP TO CHASSIS 9503080 | ||
| A 1805400360 | OIL PRESSURE GAUGE PIPE | |
| UP TO CHASSIS 9503718 | ||
| A 1805400860 | OIL PRESSURE GAUGE PIPE | |
| UP TO CHASSIS 9503080 | ||
| A 1805400960 | OIL PRESSURE GAUGE PIPE | |
| UP TO CHASSIS 9503718 | ||
| 123 | A 1805401360 | OIL PRESSURE GAUGE PIPE |
| FROM INSTRUMENT TO HOSE FROM CHASSIS 9503081 | ||
| A 1205400560 | OIL PRESSURE GAUGE PIPE | |
| FROM INSTRUMENT TO CONNECTING PIECE FROM CHASSIS 9503719 | ||
| A 1285420047 | CONNECTING NIPPLE | |
| FOR OIL PRESSURE GAUGE PIPE FROM CHASSIS 9503719 | ||
| A 1205400660 | OIL PRESSURE GAUGE PIPE | |
| FROM CONNECTING PIECE TO HOSE FROM CHASSIS 9503719 | ||
| A 1209970882 | HOSE PIECE | |
| DIA. 15 X 17, 20-MM LONG ORDER BY THE METER FOR BOX NUT TO OIL PRESSURE GAUGE PIPE | ||
| A 0009974782 | HOSE PIECE | |
| DIA. 15 X 17, 20-MM LONG ORDER BY THE METER FOR BOX NUT TO OIL PRESSURE GAUGE PIPE UP TO CHASSIS 9503080 | ||
| A 0009974782 | HOSE PIECE | |
| DIA. 15 X 17, 20-MM LONG ORDER BY THE METER FOR BOX NUT TO OIL PRESSURE GAUGE PIPE UP TO CHASSIS 9503080 | ||
| LOCK WASHER | ||
| B 10 DIN 127 FOR OIL PRESSURE GAUGE PIPE AT FRONT WALL AND WHEEL ARCH STRUT UP TO CHASSIS 9503718 | ||
| HEX. NUT | ||
| M 10 DIN 936-5 S FOR OIL PRESSURE GAUGE PIPE AT FRONT WALL AND WHEEL ARCH STRUT UP TO CHASSIS 9503080 | ||
| HEX. NUT | ||
| M 10 DIN 936-5 S FOR OIL PRESSURE GAUGE PIPE AT FRONT WALL AND WHEEL ARCH STRUT UP TO CHASSIS 9503718 | ||
| SPRING WASHER | ||
| A 8 DIN 137 FOR OIL PRESSURE GAUGE PIPE AND HOSE AT BRACKET FROM CHASSIS 9503081 | ||
| SPRING WASHER | ||
| A 8 DIN 137 FOR OIL PRESSURE GAUGE PIPE AND HOSE AT BRACKET FROM CHASSIS 9503719 | ||
| HEX. NUT | ||
| BM 8 DIN 439-5 S FOR OIL PRESSURE GAUGE PIPE AND HOSE AT BRACKET FROM CHASSIS 9503081 | ||
| HEX. NUT | ||
| BM 8 DIN 439-5 S FOR OIL PRESSURE GAUGE PIPE AND HOSE AT BRACKET FROM CHASSIS 9503719 | ||
| 127 | A 0009870932 | RUBBER HOSE 25 MM LONG |
| FOR OIL PRESSURE GAUGE PIPE AT BODY FRONT END | ||
| 128 | A 1369950501 | FIXING CLAMP |
| FOR OIL PRESSURE GAUGE PIPE AT BODY FRONT END | ||
| LENS-HEAD SHEET | ||
| METAL SCREW BZ 3,9X9,5 DIN 7981 FOR OIL PRESSURE GAUGE PIPE AT BODY FRONT END | ||
| A 1369950501 | FIXING CLAMP | |
| FOR CAPILLARY TUBE AT FRONT WALL | ||
| LENS-HEAD SHEET | ||
| METAL SCREW B 3,9X9,5 DIN 7981 FOR CAPILLARY TUBE AT FRONT WALL | ||
| A 1215400059 | HOSE | |
| FOR OIL PRESSURE GAUGE PIPE UP TO CHASSIS 9503080 | ||
| A 1215400059 | HOSE | |
| FOR OIL PRESSURE GAUGE PIPE UP TO CHASSIS 9503718 | ||
| 130 | A 1285400059 | HOSE |
| FOR OIL PRESSURE GAUGE PIPE FROM CHASSIS 9503081 | ||
| A 1215400259 | HOSE | |
| FOR OIL PRESSURE GAUGE PIPE FROM CHASSIS 9503719 | ||
| 131 | A 0005452209 | STOP LIGHT SWITCH |
| ALSO SEE GROUP 42 | ||
| 132 | A 0005450412 | FOOT DIMMER SWITCH |
| 132a | A 0005459124 | REVERSING SWITCH |
| FOR TURN-INDICATOR BLINKER SPECIAL REQUEST (TURN-INDICATOR BLINKER LIGHTS WITH AUTOMATIC CUTOUT FOR USA) | ||
| A 1805450037 | BLINKER LEVER KNOB, BLACK | |
| FOR REVERSING SWITCH SPECIAL REQUEST (TURN-INDICATOR BLINKER LIGHTS WITH AUTOMATIC CUTOUT FOR USA) | ||
| 132b | A 1805450237 | BLINKER LEVER KNOB, BLACK |
| FOR REVERSING SWITCH SPECIAL REQUEST (TURN-INDICATOR BLINKER LIGHTS WITH AUTOMATIC CUTOUT FOR USA) | ||
| A 1805401609 | CABLE HARNESS | |
| FOR TURN-INDICATOR BLINKER SPECIAL REQUEST (TURN-INDICATOR BLINKER LIGHTS WITH AUTOMATIC CUTOUT FOR USA) | ||
| 133 | A 1365450158 | INSULATING PLATE |
| FOR FOOT DIMMER SWITCH AT PEDAL FLOOR | ||
| LENS-HEAD COUNTERSUNK | ||
| SCREW BM 4X30 DIN 7988-4 S FOR FOOT DIMMER SWITCH AT PEDAL FLOOR | ||
| 135 | A 0009902591 | CAGE CLAMP WITH NUT |
| FOR FOOT DIMMER SWITCH AT PEDAL FLOOR | ||
| A 0009972781 | GROMMET | |
| FOR CABLE TO FOOT DIMMER SWITCH | ||
| A 1205420407 | FLEXIBLE DRIVE | |
| SHAFT, 1,750-MM LONG | ||
| 137 | A 1205420307 | FLEXIBLE DRIVE |
| SHAFT, 1,750-MM LONG | ||
| A 1839970181 | GROMMET | |
| FOR TACHOMETER SHAFT THROUGH FLOOR AND TUNNEL | ||
| A 1869970481 | GROMMET | |
| FOR TACHOMETER SHAFT THROUGH FLOOR AND TUNNEL | ||
| A 0009973181 | GROMMET | |
| FOR TACHOMETER SHAFT THROUGH FLOOR AND TUNNEL | ||
| A 0009883478 | CLAMP | |
| FOR TACHOMETER SHAFT AT PEDAL FLOOR, RIGHT | ||
| A 0009883478 | CLAMP | |
| FOR TACHOMETER SHAFT AT PEDAL FLOOR, RIGHT | ||
| 139 | A 1209950001 | FIXING CLAMP |
| FOR TACHOMETER SHAFT AT BEARING, CONTROL SHAFT | ||
| LENS HEAD SCREW | ||
| AM 5X10 DIN 7985-4 S FOR TACHOMETER SHAFT AT BEARING, CONTROL SHAFT | ||
| LOCK WASHER | ||
| B 5 DIN 127 FOR TACHOMETER SHAFT AT BEARING, CONTROL SHAFT | ||
| 142 | A 1809971281 | GROMMET |
| FOR TACHOMETER SHAFT THROUGH FORKED SUPPORT | ||
| 143 | A 1809870044 | GROMMET |
| TO SEAL 3 RD PASSAGE OF FORKED SUPPORT | ||
| 144 | A 0001545506 | THREE-ELEMENT VOLTAGE |
| 145 | A 0001540250 | GROMMET WITH |
| LOCK WASHER | ||
| B 6 DIN 127 TO FIX REGULATOR TO BRACKET, WHEEL ARCH PAN | ||
| LENS HEAD SCREW | ||
| AM 6X20 DIN 7985-4 S TO FIX REGULATOR TO BRACKET, WHEEL ARCH PAN | ||
| 148 | A 0009970781 | GROMMET |
| FOR CABLE FROM VOLTAGE REGULATOR TO GENERATOR | ||
| A 1215401709 | ADDITIONAL CABLE HARNESS | |
| SPECIAL REQUEST FOR LIGHT SWITCHING FOR VEHICLES EXPORTED TO THE USA | ||
| INSULATING HOSE | ||
| B 20X22,4 SW 100 MM DIN 40621 OVER MAIN CABLE HARNESS, LIGHT TURNING SWITCH, ORDER BY THE METER SPECIAL REQUEST FOR LIGH | ||
| A 0005450301 | ADDITIONAL FUSE | |
| BOX, 2-POLE AT FRONT WALL SPECIAL REQUEST FOR LIGHT SWITCHING FOR VEHICLES EXPORTED TO THE USA | ||
| CYLINDRICAL SCREW | ||
| AM 4X15 DIN 84 FOR FUSE BOX AT FRESH-AIR DUCT SPECIAL REQUEST FOR LIGHT SWITCHING FOR VEHICLES EXPORTED TO THE USA | ||
| A 0005427320 | REPLACED BY 001542 20 20 | |
| A 0005424420 | REPLACED BY 001542 20 20 | |
| A 0015420720 | REPLACED BY 001542 20 20 | |
| 150 | A 0015422020 | HORN |
| A 0005427120 | HORN | |
| SPECIAL REQUEST SIGNAL SYSTEM FOR CARS EXPORTED TO FRANCE | ||
| A 0005424520 | HORN | |
| A 0015420820 | HORN | |
| SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 0005424620 | HORN | |
| SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| HEX. HEAD SCREW | ||
| M 10X28 DIN 931-8 G FOR HORN AT BRACKET SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| LOCK WASHER | ||
| B 10 DIN 127 FOR HORN AT BRACKET SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| HEX. NUT | ||
| M 10 DIN 934-5 S FOR HORN AT BRACKET SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| 152 | HEX. HEAD SCREW | |
| M 10X28 DIN 931-8 G FOR HORN AT BRACKET | ||
| 153 | LOCK WASHER | |
| B 10 DIN 127 FOR HORN AT BRACKET | ||
| 154 | HEX. NUT | |
| M 10 DIN 934-5 S FOR HORN AT BRACKET | ||
| A 101206120031 | BRACKET | |
| FOR HORN AT CROSS TUBE, FRONT SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 1205420440 | BRACKET | |
| FOR HORN SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| HEX. HEAD SCREW | ||
| M 6X15 DIN 933-8 G FOR BRACKET AT LEFT WHEEL HOUSE SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| LOCK WASHER | ||
| B 6 DIN 127 FOR BRACKET AT LEFT WHEEL ARCH PAN SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| WASHER | ||
| A 6,4 DIN 9021 FOR BRACKET AT LEFT WHEEL ARCH PAN SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| HEX. NUT | ||
| M 6 DIN 934-5 S FOR BRACKET AT LEFT WHEEL ARCH PAN SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| LOCK WASHER | ||
| B 4 DIN 127 FOR CABLE CONNECTION AT HORN SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| CYLINDRICAL SCREW | ||
| AM 4X8 DIN 84-4 S FOR CABLE CONNECTION AT HORN SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| LOCK WASHER | ||
| B 4 DIN 127 FOR CABLE CONNECTION AT HORN | ||
| CYLINDRICAL SCREW | ||
| AM 4X8 DIN 84-4 S FOR CABLE CONNECTION AT HORN | ||
| 160 | A 0001580003 | IGNITION COIL |
| 161 | A 0001580240 | FIXING CLAMP |
| FOR IGNITION COIL | ||
| CYLINDRICAL SCREW | ||
| BM 5X40 DIN 84-4 S | ||
| SQUARE NUT | ||
| M 5 DIN 562 | ||
| HEX. HEAD SCREW | ||
| M 6X12 DIN 933-8 G FOR IGNITION COIL AT WHEEL ARCH PAN | ||
| LOCK WASHER | ||
| B 6 DIN 127 FOR IGNITION COIL AT WHEEL ARCH PAN | ||
| WASHER | ||
| A 6,4 DIN 9021 FOR IGNITION COIL AT WHEEL ARCH PAN | ||
| HEX. NUT | ||
| M 6 DIN 934-5 S FOR IGNITION COIL AT WHEEL ARCH PAN | ||
| 167 | A 0005460235 | RUBBER PROTECTIVE CAP |
| FOR IGNITION COIL | ||
| A 0005421519 | CONTACTOR | |
| SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 0005422719 | CONTACTOR | |
| SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 1215400044 | PUSH - BUTTON SWITCH | |
| FOR 3RD HORN SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 1365450672 | ESCUTCHEON | |
| SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 0009972040 | FELT RING | |
| SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 1363020901 | BUTTON | |
| SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 1215400609 | ADDITIONAL CABLE HARNESS | |
| SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 1215400509 | ADDITIONAL CABLE HARNESS | |
| FROM 2ND TO 3RD HORN SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 1215400138 | ELECTRICAL CABLE | |
| FROM FUSE BOX TO RELAY TERMINAL 30/51 SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 1215400238 | ELECTRICAL CABLE | |
| FROM RELAY TERMINAL 87 TO 2ND HORN SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 1215400338 | GROUND CABLE | |
| FROM 2ND HORN TO GROUND SPECIAL REQUEST FOR TRIPLE-TONE SIGNAL SYSTEM | ||
| A 0005451325 | SOCKET FOR HAND LIGHT | |
| SPECIAL REQUEST | ||
| ELECTRICAL CABLE, | ||
| BLACK 1,000-MM LONG A 1 DIN 72551 ORDER BY THE METER SPECIAL REQUEST | ||
| INSULATING HOSE, | ||
| BLACK 950-MM LONG B 3X3,8 DIN 40621 ORDER BY THE METER SPECIAL REQUEST | ||
| CYLINDRICAL SCREW | ||
| AM 5X10 DIN 84-4 S FOR BRACKET AT WHEEL ARCH PAN, LEFT SPECIAL REQUEST | ||
| LOCK WASHER | ||
| B 5,3 DIN 127 FOR BRACKET AT WHEEL ARCH PAN, LEFT SPECIAL REQUEST | ||
| HEX. NUT | ||
| M 5 DIN 934-5 S FOR BRACKET AT WHEEL ARCH PAN, LEFT SPECIAL REQUEST |
© 2010-2013 UAB "RPV" Paslaugų teikimo sąlygos - Privatumo politika - Kopijuoti ir naudoti komerciniais tikslais draudžiama